Go Back
HOME
page / Click here
EAS - EXPANDABLE
STARTER KIT - CABLE
( WITH - EGT )
FOR:
CTS AND CS
The EGT probe is a sensor that allows users to monitor critical Exhaust
Gas Temperatures to ensure added power is not creating excessive heat which,
in turn, can cause engine damage. With the EAS system a user can connect
multiple EGT sensors to monitor temperatures in different locations and
compare readings to be even more precise.
The Edge Accessory System ( EAS ) was created with future expandability
in mind. The architecture of the EAS allows users to connect multiple
accessories, daisy-chain style, to the CS and CTS platform. The ability to
daisy-chain multiple accessories using the EAS allows users to monitor and
display dozens of parameters on a single device.
*EAS Starter Kits are only available to work with the CS and CTS product
lines. In order to use the EAS accessories you must have an EAS Starter kit (
part # 98602
) or ( part # 98603 / Found on this Page.) EAS Starter kits come with all
Juice w/ Attitude CS and CTS products,
NOTE:
1.) START - WITH THE EAS - STARTER KIT
2.) NEXT - EAS SENSOR SYSTEM - ( PLUGS INTO STARTER KIT )
3.) NEXT - YOUR CHOICE OF SENSORS - ( PLUGS INTO EAS SENSOR
SYSTEM )
Expand your CS or CTS with the EAS sensors!
The Edge Accessory System (EAS) was created with future expandability in
mind. The architecture of the EAS allows users to connect multiple
accessories, daisy-chain style, to the CS and CTS platform. The ability to
daisy-chain multiple accessories using the EAS allows users to monitor and
display dozens of parameters on a single device.
Add up to 16 additional sensors with the EAS Universal Sensor Input.
Then setup, configure, and customize those sensors through Edge’s MyStyle
software package. The Edge MyStyle software will recognize any Universal
Sensor Input that has been connected to your CS or CTS and allow the user to
change the PID name, gauge name, description and units. The user can choose
from a number of preconfigured sensors or enter in a custom look-up table to
translate the input voltage to the measured parameter value and units.
EAS UNIVERSAL SENSOR INPUT
The EAS Universal Sensor Input provides the ability to read any 0-5
volt signal and translate that signal a meaningful value for display on the
Edge CS or CTS. This means you can add custom temperature, pressure, Air/Fuel
and even Travel/Position gauges to your Edge CS and CTS! Using the Edge
Accessory System provides the following benefits:
• Using the MyStyleTM software, sensors can be easily configured and
renamed.
• Up to 8 Universal Sensor Input accessories may be installed in any
order on the vehicle. Each Universal Sensor Input will support up to 2 sensors
for a total of 16 additional sensors that can be added to your CS or CTS
device.
NOTE: Sensors from manufacturers other than Edge can also be attached to
a CS or CTS device through the EAS Universal Sensor Input
• Eliminates the necessity of routing multiple wires to the CS / CTS
Monitor
EAS PRESSURE SENSOR
Edge’s EAS Pressure Sensor is a 0 - 100 PSIg 1/8” NPT sensor that
plugs directly into the Universal Sensor Input system (p/n 98605). Edge’s
Pressure Sensor comes equipped with the proper wires and connectors to plug
right into the Universal Sensor Input system saving time and money on cutting,
splicing, and crimping wire terminals to connect the sensor. Use Edge’s
Pressure Sensor to monitor data such as Boost PSI, Fuel Rail Pressure, Air Bag
Pressure, Lift Pump Pressure, Pre and Post Intercooler Pressure and many more.
EAS TEMPERATURE SENSOR
The EAS Temperature Sensor is a -40°F to 300°F 1/8” NPT
supplied with the connectors to plug directly into Edge’s Universal Sensor
Input System. Using Edge’s Temperature Sensor you can monitor Transmission
Temp., Differential/Axle Oil Temp., Oil Temp., Engine Coolant Temp., Air
Intake Temp., Pre and Post Intercooler Temp., and many more. Use this in
conjunction with the Universal Sensor Input and the CS or CTS monitor to allow
you to view critical temperatures with the most state-of-the-art product on
the market today.
EAS AMBIENT TEMPERATURE SENSOR
If your vehicle is not equipped with an outside temperature
sensor then this is a must have! The EAS Ambient Temperature Sensor is a -40°F
to 230°F Waterproof 0.2” diameter sensor ready to plug into Edge’s Universal
Sensor Input system. Now you’ll never wonder what outside air temperature is
again!
NOTE:
TURBO TIMERS - PLUG DIRECTLY INTO THE - EAS - STARTER
KIT