Go Back HOME page / Click here
EAS - EXPANDABLE
STARTER KIT with 15 inch Exhaust Gas Temperature Probe
Monitor critical exhaust gas temperatures to avoid engine
damage from excessive heat while operating at higher power
levels on diesel engines. Expand monitoring with the edge
excessory system which allows for mutiple sensors to monitor
temperatures in different locations.
*EAS Starter Kits are only available to work with the
CTS2 /CTS and CS2 / CS product lines.
1.) START - WITH THE EAS - STARTER KIT
2.) NEXT - EAS SENSOR SYSTEM - ( PLUGS INTO STARTER KIT )
3.) NEXT - YOUR CHOICE OF SENSORS - ( PLUGS INTO EAS SENSOR SYSTEM )
Expand your CTS2 or CS2 with the EAS sensors!
The Edge Accessory System (EAS) was created with future expandability in mind. The architecture of the EAS allows users to connect multiple accessories, daisy-chain style, to the CS and CTS platform. The ability to daisy-chain multiple accessories using the EAS allows users to monitor and display dozens of parameters on a single device.
Add up to 16 additional sensors with the EAS Universal Sensor Input. Then setup, configure, and customize those sensors through Edges MyStyle software package. The Edge MyStyle software will recognize any Universal Sensor Input that has been connected to your CTS2 or CS2 and allow the user to change the PID name, gauge name, description and units. The user can choose from a number of preconfigured sensors or enter in a custom look-up table to translate the input voltage to the measured parameter value and units.
EAS UNIVERSAL SENSOR INPUT
The EAS Universal Sensor Input provides the ability to read any 0-5 volt signal and translate that signal a meaningful value for display on the Edge CTS2 or CS2. This means you can add custom temperature, pressure, Air/Fuel and even Travel/Position gauges to your Edge CS and CTS! Using the Edge Accessory System provides the following benefits:
- Using the MyStyleTM software, sensors can be easily configured and renamed.
- Up to 8 Universal Sensor Input accessories may be installed in any order on the vehicle. Each Universal Sensor Input will support up to 2 sensors for a total of 16 additional sensors that can be added to your CTS2 or CS2 device.
NOTE: Sensors from manufacturers other than Edge can also be attached to a CS or CTS device through the EAS Universal Sensor Input
- Eliminates the necessity of routing multiple wires to the CTS2 / CTS / CS2/ CS Monitor
EAS PRESSURE SENSOR
Edges EAS Pressure Sensor is a 0 - 100 PSIg 1/8 NPT sensor that plugs directly into the Universal Sensor Input system (p/n 98605). Edges Pressure Sensor comes equipped with the proper wires and connectors to plug right into the Universal Sensor Input system saving time and money on cutting, splicing, and crimping wire terminals to connect the sensor. Use Edges Pressure Sensor to monitor data such as Boost PSI, Fuel Rail Pressure, Air Bag Pressure, Lift Pump Pressure, Pre and Post Intercooler Pressure and many more.
EAS TEMPERATURE SENSOR
The EAS Temperature Sensor is a -40F to 300F 1/8 NPT supplied with the connectors to plug directly into Edges Universal Sensor Input System. Using Edges Temperature Sensor you can monitor Transmission Temp., Differential/Axle Oil Temp., Oil Temp., Engine Coolant Temp., Air Intake Temp., Pre and Post Intercooler Temp., and many more. Use this in conjunction with the Universal Sensor Input and the CS or CTS monitor to allow you to view critical temperatures with the most state-of-the-art product on the market today.
EAS AMBIENT TEMPERATURE SENSOR
If your vehicle is not equipped with an outside temperature sensor then this is a must have! The EAS Ambient Temperature Sensor is a -40F to 230F Waterproof 0.2 diameter sensor ready to plug into Edges Universal Sensor Input system. Now you will never wonder what outside air temperature is again!
TURBO TIMERS - PLUG DIRECTLY INTO THE - EAS - STARTER KIT